•  

    Pleated Element Filters

    LAMELLEN-JET

    The lamella filter LAMELLEN-JET with pneumatical cleaning combines maximum filter area with minimum space required, and as a standing filter range it is suitable for dry separation of all pourable dusts and bulk materials.

     

    Pneumatic Cleaning

     

       Continue below...    
     
  •  
     

    Pleated Element Filters

    LAMELLEN-JET-S

    The LAMELLEN-JET type S, consists of a cleanable lamella filter system with downstream particulate filter cassette. This way a residual dust content of < 0.001 mg/m³ is achieved.

     

    Pneumatic Cleaning

     

       Continue below...    

  Pleated Element Filters LAMELLEN-JET

The lamella filter LAMELLEN-JET with pneumatical cleaning combines maximum filter area with minimum space required, and as a standing filter range it is suitable for dry separation of all pourable dusts and bulk materials. LAMELLEN-JET filters can be configured for air flow rates from 2,000 to 40,000 m³/h and customized.

Standard Design :

  • Closed basic module consisting of raw gas chamber with dust discharge hopper and supporting legs
  • Clean gas chamber with filter elements
  • Pneumatic cleaning unit
  • Housing strength up to +/- 45 mbar g
  • Modular system for flexible adaptation to each application
  • Removing of self-supporting filter elements on the clean gas side

Pneumatic Cleaning

 

Options :

  • All housing and built-in units or components in contact with the product/dust are made of stainless steel
  • Explosion protected design according to directive 94/9/EG (ATEX)
  • Explosion pressure-shock resistant design for reduced explosion over pressure (e.g. 0.4 bar g or 2.0 bar g) with pressure relief
  • Electronic control unit for filter cleaning controlled by time or differential pressure and for additional components (fan, rotary valve...)
  • Control system and motors for special voltages
  • Design for hot gases up to 110°C
  • Filter media available in different qualities (e.g. FDA-conform for food industry)
  • Sound absorbing options for use in noise-sensitive environments
  • Electric filter housing heating including thermal insulation
  • Various accessories, e.g. dust collecting container, butterfly valve, rotary valve, double pendulum valve, screw conveyor, level indicator within dust bin, flange-mounted or console-mounted fan, inspection cover, secondary filter stage

  Pleated Element Filters LAMELLEN-JET-S

The LAMELLEN-JET type S, consists of a cleanable lamella filter system with downstream particulate filter cassette. This way a residual dust content of < 0.001 mg/m³ is achieved.

The 1st filter stage is regenerated by jet pulses of compressed air, the 2nd filter stage serves as so called safety filter and is changed after reaching its saturation limit. The lamella elements can be precoated additionally or run with a continuous addition of additives. The filter surface is much larger compared to flat filter elements because of the pleated filter fleece. 

Fields of application of this lamella filter are mainly within the chemical and pharmaceutical industry for de-dusting almost all dry dust kinds and also for slightly adhesive dusts.

 

Standard Design :
  • Closed basic module consisting of raw gas chamber with dust discharge hopper and supporting legs
  • Clean gas chamber with filter elements
  • Pneumatic cleaning unit for the 1. filter stage
  • Housing strength up to +/- 45 mbar g
  • Modular system for flexible adaptation to each application
  • Filter media change from the clean gas side (1st and 2nd filter stage)

Pneumatic Cleaning


Options :
  • All housing parts, internal parts or components in contact with the product made of stainless steel
  • Explosion protected design according to directive 94/9/EG (ATEX)
  • Explosion pressure-shock resistant design for reduced explosion overpressure (0.4 bar g) with explosion pressure relief
  • Electronic control unit for filter cleaning controlled by time or differential pressure and for additional components (fan, rotary valve...)
  • Control system and motors for special voltages
  • Design for hot gases up to 110°C
  • Filter media available in different qualities (e.g. FDA-conform for food industry)
  • Sound absorbing options for use in noise-sensitive environments
  • Electric heating of filter housing including thermal insulation
  • Various accessories, e.g. dust collecting bin, shut-off valve, rotary valve, double pendulum valve, screw conveyor, level indicator within dust bin, fan flanged at filter or mounted on a bracket, inspection cover

 

This site uses cookies to improve your experience and to provide services in line acon your preferences. By closing this banner, scrolling this page or by clicking any of its elements consent to the use of cookies. If you want to know more or refusing consent to all or some cookies go to the Cookies Policy